The MI424WR would then request its IP from the WRT1900AC, but i couldn't get the MI424WR's WAN port to actually work. This config should have had the MI424WR providing a bridge to the WRT1900AC, which would DHCP an IP from Verizon. I have already tried to set up the MI424WR as a MoCA bridge, providing internet and passing DHCP to the WRT1900AC, but I couldn't get the config to work (if anyone has done this and would like to share their settings, let me know). If not, could I use a MoCA LAN adapter like the ECB6200 in place of the MI424WR to provide that guide data while still having the Linksys router as the only router, connected via ethernet to the ONT and providing internet to the ECB6200 via a WRT1900AC LAN ethernet port? Many people have done this, but I'm not sure if the STB will still be provided with VOD/guide data directly from the ONT. Have Verizon provision the ONT to provide internet service via ethernet. I have a Linksys WRT1900AC router that I wish to use as the primary router. Right now, my apartment is wired throughout with coax from the ONT with an ActionTec MI424WR Rev I that provides our internet service (we have internet + TV with a single STB). If you find this post useful, please give the author a "Solution", or mark as "Kudo", if it solves your problem, thank you very much.Hi all, I've done some extensive googling on this subject and I think I have a solid plan, but I'm not sure if it will actually work as I haven't seen anyone do exactly what I'm considering. If you find this post useful, please give the author a "Solution", or mark as "Kudo", if it solves your problem, thank you very When I turn on port bridging and connect my router should I be able to see it in the "Home Network" view on T3200M of connected devices? What confuses me is just where the fiber is being converted to either Coax or Ethernet from the fibre signal. The one thing taht I would make sure of is that your MoCa adapters are 2.5 MoCa compatible as this is the newest standard and will support faster speeds between devices. No need for Bridge Mode if the T3200M is not inline at all. That coax signal is being reconverted to Ethernet and feed to the T3200M router at that location, If the is a correct assumption on my part, I would just suggest the you remove the T3200M from the system and plug your aftermarket router where you have the T3200M currently. That Ethernet signal is be feed to a MoCa adapter and sent via coax to another location in the residence. You have Telus fibre coming into the residence to some device that outputs a Ethernet type signal. The other part of your question above raises a few questions for me. The only way to correct this is to reset the T3200M back to factor/basic mode to get t the interface. In most cases if you have "Bridged Mode" turned on your T3200M you'll not be able to get to the routers web interface. Will this work with the ethernet from the MoCA upstairs going into the WAN port of the modem that I want to flip to bridge mode? My understanding is when bridge mode is on only port1 works? So how do I set this up with these MoCA devices going into the modem? Is still as simple as bridge mode on then ethernet cable in port1 to my gaming When I turn on port bridging and connect my router should I be able to see it in the "Home Network" view on T3200M of connected devices? Is the upstairs MoCA necessary if it is just being used to connect to the T3200M, which apparently has onboard MoCA capabilities? My roommate said it was necessary for fibre setup, but I'm doubtful.Ģ. I am new to using MoCA so I have a couple of questions:ġ. We would like a better WiFi experience with my personal gaming router, so I imagined I could simply enable bridge mode on the T3200M and plug in my router to port1. On the second floor this coaxial comes out of the wall to a second MoCA adapter that converts back to ethernet and goes into the T3200M modem which acts as the current router as well for the house. Here's the internet wiring situation: ONT box in basement sends copper signal to MoCA adapter that connects to house coaxial which goes upstairs. However I have some confusion with how my roommates Telus Fibre Internet home setup affects this. I would like to bridge our homes T3200M Modem to a personal gaming router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |